Sliding Door Frames
1 1/2" Sliding Door Frames
Quick Frames
White Aluminum Quick Frames can be assembled with standard 2 x 4 lumber or galvanized Steel Box Girts as horizontals. We recommend spacing these horizontals approximately 24" to 28" on center. Wood or steel inserts can be placed inside the vertical channel between each horizontal. Inserts should be permanently attached with screws, becoming part of the frame. This is suggested to help prevent damage to the doors in windy conditions. Use self tapping tek screws.
White Aluminum
|
1001 White Aluminum Quick Frame Is lumber fit for standard 2 x 4 or 2 x 6 and provides smooth, safe sides for door openings. Packaged in pieces, bundled per order, available in 8', 10', 12', 14', and 16' lengths. |
|
1002 White Aluminum H-Frame Designed for use with bi-parting doors, provides concealed mating between units covering both door edges. Packaged in pieces, bundled per order, available in 8', 10', 12', 14', and 16' lengths. |
|
1003 White Aluminum Bottom Rail Attaches to bottom of door and accepts the #64 Rail Guide to firmly anchor and guide door along building during operation. Order for doors 1-1/2" thick. Available in 8', 10', 12', 14', 16', 18', and 20' lengths. |
|
1005 White Aluminum Bottom Rail Mounts on face of wood bottom rail and provides a smooth surface for a stay roller. Available in 8', 10', 12', 14', 16', 18', and 20' lengths. |
3 1/2" Sliding Door Frames
Quick Frames
Quick Frames
Box Girt/Horizontal
|
2004 Galvanized Steel Girt Made from 20 gauge galvanized steel (1-1/2" x 3-1/2" lock seamtube). Can be used in place of wood horizontal girts to eliminate warping, bowing, and cracking of door panels. Weight is 1.3 lbs./ft. Available in 6' - 20' lengths. |
Tab-Loc Steel Sliding Door Frame
For Box and Round Rail Systems
For Box and Round Rail Systems
|
Materials Checklist
1. Rail Cover 2. Rail 3. Rail Bracket 4. Hanger 5. Steel Lateral 6. Pre-finished Steel Vertical 7. Door Covering/Siding 8. Guide Rail Bracket 9. Guide Rail *10. Center Guide & Stop (For Bi-parting Doors) *10a. Center Guide (For Larger, Single Doors) *11. Door Stop (Bottom Mount) *11a. Door Stop (Jamb Mount) *12. Jamb Latch *12a. Center Door Latch (For Bi-parting Doors) *13. Door Pull *14. Door Astragal *Note: These items are not shown in the diagram, but are required for a complete door system installation. |
|
Tab-Loc lets one man assemble a steel door frame in 10 minutes!
The secret is our exclusive, patented locking tabs. These built-in fasteners are pre-punched into the frame members. Just bend the tabs down into matching slots for a square, tight, permanent steel door frame. Unlike any other door frame, you do not even need a level area for assembly. Once you are familiar with Tab-Loc, 10 minutes is all it takes to get a frame ready to attach the siding. In fact, the door can be completed and hung in under an hour to previously installed rail.
The secret is our patented Tab-Loc system.
The secret is our exclusive, patented locking tabs. These built-in fasteners are pre-punched into the frame members. Just bend the tabs down into matching slots for a square, tight, permanent steel door frame. Unlike any other door frame, you do not even need a level area for assembly. Once you are familiar with Tab-Loc, 10 minutes is all it takes to get a frame ready to attach the siding. In fact, the door can be completed and hung in under an hour to previously installed rail.
The secret is our patented Tab-Loc system.
1. Align tabs over slots in cross members.
3. Tighten tabs halfway, then square up frame.
|
Insert screwdriver blade to start tab.
Lock tabs permanently with our special tapered tool. #6000T
To Shorten Door Lateral - Cut off desired amount and replace the square hole lost in the cut-off with 7/8" diameter round hole.
To Shorten Door Vertical - Extra tabs on both ends allow shortening in 1.5" increments up to 12".
|
Applications for Installing Sliding Door on Building
After door frame has been completely assembled, fasten siding to frame. Install hangers and hang door.
After door frame has been completely assembled, fasten siding to frame. Install hangers and hang door.
Bottom Guide Systems and Accessories
|
#1003 Aluminum Bottom Rail Attaches to bottom of door and accepts the #64 Guide Rail to firmly anchor and guide door along building during operation. Order for doors 1-1/2' thick. White powder coated. Available in the following lengths: 8' 10' 12' 14' 16' 18' 20' |
|
#60 Guide Rail Bracket For use with #64 Guide Rail. Slotted hole in each leg allows both lateral and vertical adjustments. Bolts and nuts included. |
|
#68 Single Door Stop For use with #64 Bottom Door Guide. Stops door and prevents from disengaging with guide rail. |
|
#64 Guide Rail Fabricated from 16 gauge galvanized steel and mounts with #60 brackets. Engages the bottom door guides to hold the door in place and prevent wind damage. Available in the following lengths: 4' 6' 8' 10' |
Optional Hardware
|
#520 Center Guide/Stop Installs on 6 x 6 post or in concrete, in the center of split doors or a large single door. For use in pairs. |
|
#790 Center Door Guide Adjustable for single sliding doors 1-1/2' to 3-1/4' thick. Install as shown with screws and lead anchors after final adjustments have been made to level and plumb the door. |